12/02 P/N 211446D1Toll-Free Customer Service Number for U.S: 1-800-558-5234Internet Address: http://www.hydra-rib.comIMPORTANT! Have any questions?..
10P/N 211446D 12/0215. Rotate jack handle clockwise to raise H-frame (13) toapproximately 7’ (2.1 m) from ground. Secure crank jack(20) to jack brac
1112/02 P/N 211446DRIM ASSEMBLY & INSTALLATION WARNING17. Install carriage bolt (41) through rim (25),washers (4) and (27) as shown. Tightennut
12P/N 211446D 12/0220. 253940Insert spacer (45) through rim assembly (25). Place rim assembly on bracket (39) so that carriage bolt (41) isinserted th
1312/02 P/N 211446D22. 23. 24. Apply logo label (33) to cover plate (31). Installcover plate (18) on rim (25) using self tappingscrews (32) as shown.
14P/N 211446D 12/02Apply height adjustmentlabel (37) to front of poleas shown.26. 10 feet(3.05 m)REGULATION RIM HEIGHT IS 10 FEET (3.05 m).3725. Check
1512/02 P/N 211446D27. A. LOWER BACKBOARD UNTIL RIM IS 7 FEET OFF THE GROUND.B. APPLY THIN WHITE STRIP TO BOTTOM EDGE OF OUTER CRANK TUBE AS SHOWN.C.
16P/N 211446D 12/02Rotate crank handle to raise and lower backboard.NOTE: If height adjustment is difficult to operate, you mayhave over tightened the
1712/02 P/N 211446DItem Qty. Part No. Description1 4 200573 J-Bolt, 5/8”-11”2 12 265575 Nut, Hex 5/8”-11”3 1 920880 Mounting Plate4 8* 203470 Washer,
18P/N 211446D 12/02Item #41 (1)Item #24 (8)Item #30 (1)Item #32 (2)Item #28 (1)Item #23 (4)Item #42 (2)HARDWARE IDENTIFIERItem #44 (1)Item #45 (1)Item
2P/N 211446D 12/02IMPORTANT! WRITE MODEL NUMBER FROM BOX ONTO PAGE 1 OF THIS OWNERS MANUALWARNING FAILURE TO FOLLOW THESE WARNINGS MAY RESULTIN S
24" (61 cm)36" (91.4 cm)Ensure ground is level with playingsurface, then dig pole hole.GROUND SURFACEPLAYINGSURFACE1. Install threaded ends
4P/N 211446D 12/02Fill hole with concrete. Tamp down concreteto release air pockets and build drainage hill.Insert J-bolts (1) from mounting plate (3
512/02 P/N 211446DUpright pole (5). Assemble lower pole flange ontoprotruding J-bolts (1) as shown. The flange willthen rest on the nuts (2) from St
6P/N 211446D 12/028. Insert caps (8) into end of each support arm (9 &10) as shown. Tap firmly in position.Apply logo label (11) to lower support
712/02 P/N 211446D11. 1614391471314107141071416147149161416THREE PERSON MINIMUM REQUIREDFOR THIS PROCEDURE. NOTFOLLOWING RECOMMENDATION MAYRESULT IN
Position U-joint of crank jack (20) as shown.Where tubes on crank jack join, hold steadyto keep both tubes from rotating. Rotatehandle clockwise on c
912/02 P/N 211446D14. Install crank jack (20) U-joint to lower setof support arms (10) as shown.101420714211210THREE PERSON MINIMUM REQUIREDFOR THIS P
Comments to this Manuals