Huffy DH9300 User Manual

105/03 P/N 211689C© COPYRIGHT 2000 by HUFFY SPORTSToll-Free Customer Service Number for U.S: 1-800-558-5234,For Canada: 1-800-284-8339,For Europe: 00

10P/N 211689C 05/03IMPORTANT! Holes in top (1) and bottom pole (3) sections MUST align tocorrectly position elevator system toward playing surface.Whi

05/03 P/N 211689C11TOOLS REQUIRED FOR THIS SECTIONHARDWARE USED IN THIS SECTION(not actual size)SECTION B: ASSEMBLE THE BASE 1/2” & 9/16”9/16” &am

12P/N 211689C 05/031.2.Insert axle (5) through wheel bracket (4). Secure wheels (65) toaxle using pushnuts (7). Carefully tap pushnuts onto axle withh

05/03 P/N 211689C133.Install rod (12) through holes in bottom pole section (3) and eyebolt (13).Insert pole assembly into tank (8) and through center

14P/N 211689C 05/034.10111145143151414Secure tank struts (14) to pole as shown. Place cap (15) over exposed end of bolt as shown.Rotate non-secured en

05/03 P/N 211689C155.6.Secure ends of tank struts (14) to tank as shown. Repeat for oppositeside.Install upper pivot bracket (16) to front of base us

16P/N 211689C 05/03Insert bolt (21) through lower pivot bracket (17) as shown; bolt (21)will be secured during step 10. Carefully place base assembly

05/03 P/N 211689C17Install wheels (6) onto axle (5) and wheel bracket (4) with push caps(7) as shown.Position base as shown. Secure wheel bracket asse

18P/N 211689C 05/03TOOLS REQUIRED FOR THIS SECTIONHARDWARE USED IN THIS SECTION(not actual size)SECTION C: ASSEMBLE THE ELEVATOR SYSTEM & BACKBOAR

05/03 P/N 211689C196059255824Slide shroud (25) back to expose bracket and assemble gas strutcomponents as shown. Do not over-tighten.Carefully place e

2P/N 211689C 05/03BEFORE YOU START!To ensure optimal playability of backboard system, a close tolerance fit between the elevatorcomponents and hardwar

20P/N 211689C 05/03586261282763Attach plastic lever (63) toheight adjustment shroud(27) with bolt (62) and nut(58) as shown.Attach height label (61) t

05/03 P/N 211689C216.28Remove nuts from free end of cable. Insert cable into height adjustment tube asshown (FIG. A). Pull cable through end of tube (

22P/N 211689C 05/0313435373735393535334140408.Identify elevator tubes.Install triangle plates (33) and elevator tubes (35) to top pole section (1) as

05/03 P/N 211689C23374242404040379.10.Attach elevatoradjustment tube(28) to elevatortubes (35) with bolts(40) spacers (42)and nuts (37) asshown.Attach

24P/N 211689C 05/03374011.Attach front of gas strut assembly to elevator tubes (35) by rotatingelevator tubes (35) and inserting bolt (40) and nut (37

05/03 P/N 211689C2549464647474848Assemble brackets (49) to backboard using bolts (47) spacers (46) and nuts (48) asshown. The spacers may fit very tig

26P/N 211689C 05/0340353542424937Assemble lower elevator tubes (35) and rim to brackets (49) using bolt (40),spacers (42), and nut (37) as shown.14.IM

05/03 P/N 211689C2735354042493742Assemble upper elevator tubes (35) to brackets using bolt (40), spacers (42),and nut (37) as shown. 15.

28P/N 211689C 05/03SECTION D: INSTALL FRONT COVER & HANDLE1.Attach front cover (50) to hinge tubes (18) usingcarriage bolt (61) and flange nuts (1

05/03 P/N 211689C29292829283.Install trigger (29) onto cable as shown.28442.Re-install nuts and washer as shown. It is veryimportant to leave 1/8” of

05/03 P/N 211689C3WARNING FAILURE TO FOLLOW THESE WARNINGS MAY RESULTIN SERIOUS INJURY AND/OR PROPERTY DAMAGE.Owner must ensure that all players kno

30P/N 211689C 05/03312930324.Install handle (30) to height adjustment assembly withscrews (32) as shown. Be sure washer is seated inslot on handle as

05/03 P/N 211689C311.SECTION E: INSTALL NET CLIPS AND NETWARNING: Use of this product without properinstallation of net clips, or when a

32P/N 211689C 05/03Insert net into bottom of clip as shown.SIDE VIEWTwist net until it snaps into position.Net must be centered through clip. NETNETCL

05/03 P/N 211689C331.SECTION F: SECURING THE SYSTEMRoll assembly to desired playing area. Secureassembly to ground using strap (56) and tie down stak

34P/N 211689C 05/03202052 02/03MOVING SYSTEM1. Adjust basketball backboardheight to lowest position.2. Rotate handle forward untilwheels engage ground

05/03 P/N 211689C3559SECTION H: TROUBLESHOOTING GUIDE1.If the elevator is still difficult to operate, verify that the valve located on the strut isful

4P/N 211689C 05/03IMPORTANT!Remove all contents from boxes.Be sure to check inside pole sections;hardware and additional parts are packed inside.NOTIC

05/03 P/N 211689C5Get to know the basic parts of your basketball system...FRONTTOP POLEBACKMIDDLE POLEFRONTCOVERRIMBOTTOMPOLESTRUTSELEVATORASSEMBLYB

6P/N 211689C 05/03Item Qty Part No Description1 1 900467 Top Pole Section2 1 904811 Middle Pole Section (with Label)3 1 903407 Bottom Pole Section4 2

05/03 P/N 211689C7HARDWARE IDENTIFIERItem #7 (2)Item #10 (1)Item #11 (7)Item #15 (1)Item #19 (1)Item #20 (5)Item #21 (1)Item #22 (16)Item #23 (1)Item

8P/N 211689C 05/03202052 02/03MOVING SYSTEM1. Adjust basketball backboardheight to lowest position.2. Rotate handle forward untilwheels engage ground.

05/03 P/N 211689C9SECTION A: ASSEMBLE THE POLES 2.1.Wood Scrap215"(13 cm)5"(13 cm)132Correctly identify each pole section. Mark pole section