112/05 P/N M880102© COPYRIGHT 2005 by SPALDINGInground SystemOwners ManualCustomer Service Center• N53 W24700 South Corporate Circle • Sussex, WI 5308
10P/N M880102 12/05XG08.EPS20533418" (42.7 cm)6" (15.2 cm)24" (61 cm)PLAYING SURFACESUPERFICIE DE JUEGOGROUND SURFACESUPERFICIE DEL PI
12/05 P/N M880102113.Snap two halves of ground sleeve (4) together. Insert and securebottom pole section (3) into ground sleeve (4) by tighteninggroun
12P/N M880102 12/051" (2.54 cm)1" (2.54 cm)1" (2.54 cm)SIDE VIEWVISTA LATERALFIG. AFLANGEPESTAÑAInsert ground sleeve assembly and cente
12/05 P/N M8801021343Fill hole completely with concrete.Llene el orificio completamente conconcreto.6.1" (2.54 cm)1" (2.54 cm)1" (2.54
14P/N M880102 12/05After concrete has cured, remove bottom pole section from ground sleeve (4). Place anti-skid tape (6)around the bottom area of bott
12/05 P/N M880102159.Stack and bounce bottom (3) and middle (2) pole sections together. Bounce pole sections together untilmiddle section no longer m
16P/N M880102 12/0510.Stack upper pole section (1) to bottom and middle pole assembly and continue bouncing until toppole (1) no longer moves toward t
12/05 P/N M8801021711SECTION B: ASSEMBLE THE ELEVATOR TUBES TO BACKBOARDSECCIÓN B: MONTE LOS TUBOS ELEVADORES EN EL RESPALDOThis is what your system w
18P/N M880102 12/05Attach backboard support brackets (7) to the backboard frame using bolts (37) and nuts (10) as shown.Conecte los soportes del respa
12/05 P/N M880102191013121525153. Fit spacer (25) into pawl (13). Then continue to assemble using bolt (12), support brackets (15) andnut (10) as show
2P/N M880102 12/05BEFORE YOU START!¡ANTES DE COMENZAR!To ensure optimal playability of backboard system, a close tolerance fit between the elevatorcom
20P/N M880102 12/051117171321718114. Attach lower elevator tubes (11) to backboard brackets (7) using spacers (18, 19 & 22), bolts (20)ratchet (16
12/05 P/N M880102215.23241324Secure pawl (13) in place with clevis pin (23) and washers (24).Fije el fiador (13) en su lugar con un pasador de horquil
22P/N M880102 12/056.Stretch spring (26) into position with pliers.Estire el resorte (26) hasta su posición con pinzas.1326WARNING!¡ADVERTENCIA!USE EY
12/05 P/N M8801022311283939272729297Insert “T” bolt (28) through Slam Jam bracket (29) as shown. Secure Slam Jam bracket (29)assembly to backboard. Us
24P/N M880102 12/052030302111111111Attach upper elevator tubes (11) to backboard brackets (7) using spacers (30) bolt (20) and nut (21) asshown.Conect
12/05 P/N M88010225SECTION C: ATTACH THE BACKBOARD & ELEVATOR ASSEMBLY TO POLESYSTEMThis is what your system will look like when you’ve finished t
26P/N M880102 12/051.2111112020211Support pole on sawhorse. Attach backboard assembly to top pole section (1)using bolts (20) and nuts (21). Apoye el
12/05 P/N M8801022733363529283234283536ABCDE28282.Install Slam Jam Rim to Backboard Instale el borde Slam Jam en el respaldoA. Fit rim (32) securely i
28P/N M880102 12/05Place rebar with spacers into bottom pole section (3) asshown. Coloque la barra de refuerzo con los separadores en lasección inferi
12/05 P/N M88010229Fill pole with concrete approximately 1” (2.54 cm) below bottom elevator hole as shown.Llene con concreto aproximadamente 1" (
12/05 P/N M88010237-3/8" High4" WidePMS 021 for WarningOwner must ensure that all players know and follow these rules for safe operation of
30P/N M880102 12/05SECTION D: UPRIGHT, SECURE AND USE POLE SYSTEMSECCIÓN D: LEVANTE, ASEGURE Y USE EL SISTEMA DEL POSTEThis is what your system will
12/05 P/N M8801023152.1.After concrete has cured, remove tape, install pole cap (31), fit pole assembly into sleeve (4). Después de que el concreto se
32P/N M880102 12/053.10 ft.(3.05 m)Apply height adjustment label (14) to front of pole as shown. Regulation rim height is 10 feet (3.05 m). Aplique la
12/05 P/N M880102334.Install net (38).Instale la red (38).B.D.C.A.Peel protective film from surface of acrylicbackboard prior to use.Desprenda la pelí
4P/N M880102 12/05Eng: Dan\Tony1st Used:06/04Size = 2-3/4" x 4 Corner Radius = 3/8"Die Cut Label3.25 Mil VinylAll Temp. Permanent Adhesive1
12/05 P/N M8801025For more information on assembly, placement, properuse, and maintenance, visit The American BasketballCouncil website at http://www.
6P/N M880102 12/05PARTS LIST - See Hardware IdentifierArtículo Cant. PiezaN.º Descripción1 1 908143Sección superior del poste2 1 90812501 Sección medi
12/05 P/N M8801027#39 (4)*#17 (2)HARDWARE IDENTIFIER (BOLTS & SCREWS)HARDWARE IDENTIFIER (NUTS & WASHERS)HARDWARE IDENTIFIER (METAL SPACERS)#1
8P/N M880102 12/05#34 (1)#29 (1) #33 (1)HARDWARE IDENTIFIER (PLASTIC SPACERS & CLIPS)HARDWARE IDENTIFIER (OTHER)#30 (2)#19 (2)#22 (2)IDENTIFICADOR
12/05 P/N M8801029TOOLS REQUIRED FOR THIS SECTIONHERRAMIENTAS REQUERIDAS PARA ESTA SECCIÓNSECTION A: ASSEMBLE THE POLE SECCIÓN A: MONTAJE DEL POSTESho
Comments to this Manuals