101/03 P/N 211560HToll-Free Customer Service Number for U.S: 1-800-558-5234Internet Address: http://www.hydra-rib.comIMPORTANT! Have any questions?..
10P/N 211560H 01/0315. Rotate jack handle clockwise to raise H-frame (13) toapproximately 7’ (2.1 m) from ground. Secure crank jack(20) to jack
1101/03 P/N 211560H16. 232213TWO PERSON MINIMUM REQUIREDFOR THIS PROCEDURE. NOTFOLLOWING RECOMMENDATIONMAY RESULT IN SERIOUS BODILYINJURY AND/O
12P/N 211560H 01/03RIM ASSEMBLY & INSTALLATION WARNING17. Install carriage bolt (41) through rim (25),washers (4) and (27) as shown. Tighte
1301/03 P/N 211560H20. 253940Insert spacer (45) through rim assembly (25). Place rim assembly on bracket (39) so that carriage bolt (41) isinserted th
14P/N 211560H 01/0322. 23. 24. Apply logo label (33) to cover plate (31). Installcover plate (18) on rim (25) using self tappingscrews (32) as shown.
1501/03 P/N 211560H7726. Crank to achieve a rim height of 7’ (2.13 m) from theground. Place a mark on pole at the point where thelower support arms i
16P/N 211560H 01/03Rotate crank handle to raise and lower backboard.NOTE: If height adjustment is difficult to operate, you mayhave over tightened
1701/03 P/N 211560HItem Qty. Part No. Description1 4 206677 J-Bolt, 1/2”-13 x 24”2 8 202459 Nut, Hex 1/2”-133 1 920578 Mounting Plate4 34* 203474 Wash
18P/N 211560H 01/03Item #41 (1)Item #24 (8)Item #30 (1)Item #32 (2)Item #23 (8)Item #42 (2)HARDWARE IDENTIFIERItem #44 (1)Item #45 (1)Item #43 (1)WARR
2P/N 211560H 01/03IMPORTANT! WRITE MODEL NUMBER FROM BOX ONTO PAGE 1 OF THIS OWNERS MANUALWARNING FAILURE TO FOLLOW THESE WARNINGS MAY RESULTIN S
301/03 P/N 211560H24" (61 cm)36" (91.4 cm)Ensure ground is level with playingsurface, then dig pole hole.GROUND SURFACEPLAYINGSURFACE1. In
4P/N 211560H 01/03Fill hole with concrete. Tamp down concreteto release air pockets and build drainage hill.Insert J-bolts (1) from mounting plate (3
501/03 P/N 211560HUpright pole (5). Assemble lower pole flangeonto protruding J-bolts (1) as shown. Theflange will then rest on the nuts (2)
6P/N 211560H 01/038. Insert caps (8) into end of each support arm (9 &10) as shown. Tap firmly in position.Apply logo label (11) to lower suppo
701/03 P/N 211560H11. 1641394741074107416474916416TWO PERSON MINIMUM REQUIREDFOR THIS PROCEDURE. NOTFOLLOWING RECOMMENDATIONMAY RESULT IN SERIOU
8P/N 211560H 01/03Position U-joint of crank jack (20) as shown.Where tubes on crank jack join, hold steadyto keep both tubes from rotating. Rotateha
46901/03 P/N 211560H14. Install crank jack (20) U-joint to lower setof support arms (10) as shown.10420741210TWO PERSON MINIMUM REQUIREDFOR THIS PRO
Comments to this Manuals