108/03 P/N 211455F© COPYRIGHT 2000 by HUFFY SPORTSToll-Free Customer Service Number for U.S: 1-800-558-5234,For Canada: 1-800-284-8339,For Europe: 00
10P/N 211455F 08/033.4.1" (2.54 cm)Insert and securebottom pole section (3)into ground sleeve (4)by tightening groundsleeve cap (5).NOTE: Flared
08/03 P/N 211455F111" (2.54 cm)5.Note AMake a reference markhere for anti-skid tape.Note BKeep flange pushed downto concrete and leveled.Tamp dow
12P/N 211455F 08/031799FRONT SIDE9.Install pole mount bracket (7), bracketreinforcement (44) with carriage bolts(8) as shown. Tighten flange nuts (9)c
08/03 P/N 211455F131171110101412131310. 791515171611. Attach spacers (10, 11) to pole mount bracket (7) with bolts (12), washers (13), andnuts (14) as
14P/N 211455F 08/0324192221232012.2413.18Insert handle assemblythrough pole mountassembly as shown. Lockpole assembly in place atthe 10’ (3.05 m) mark
08/03 P/N 211455F15TOOLS REQUIRED FOR THIS SECTIONHARDWARE USED IN THIS SECTION(not actual size)SECTION B: ASSEMBLE THE BACKBOARD TO ELEVATOR TUBESASS
16P/N 211455F 08/03Use the following assembly instructions if you have a 44” molded plastic backboard (Rectangle or Fan)CAUTION:THIS BACKBOARD AND GOA
08/03 P/N 211455F17272514362628372537392526303532303529293231333333Use the following assembly instructions if you have a 48" molded plastic backb
18P/N 211455F 08/03Use the following assembly instructions if you have a a 44” steel-framed acrylic backboard.NOTE: Parts on this page are included in
08/03 P/N 211455F19Refer ToInstructionsIncluded With RimHardware For RimAssembly.Peel protective film fromsurface of acrylicbackboard prior to use.NOT
2P/N 211455F 08/03BEFORE YOU START!To ensure optimal playability of backboard system, a close tolerance fit between the elevatorcomponents and hardwar
20P/N 211455F 08/034A.4B.26303532313529293231333933272514122628Use the following assembly instructions if you have a 48” molded plastic-framed acrylic
08/03 P/N 211455F21TOOLS REQUIRED FOR THIS SECTIONHARDWARE USED IN THIS SECTION(not actual size)SECTION C: ATTACH THE BACKBOARD/ELEVATORTO POLE SYSTEM
22P/N 211455F 08/0316.13529293333333335303017.353133333030Support pole on sawhorse. Attach backboard assembly to top pole section (1). NOTE: Two peopl
08/03 P/N 211455F2318.353129291" (2.54 cm)CONCRETE119.Insert bolt (31) through left sideshort elevator tube (29), thenstretch spring or springs (
24P/N 211455F 08/0320.Install clips.CLIP “ARM”CLIP “BODY”Insert one “arm” of clip into ram as shown. Twist “body” ofclip slightly so that second “arm”
08/03 P/N 211455F25Insert net into bottom of clip as shown.SIDE VIEWTwist net until it snaps into position.Net must be centered through clip. NETNETCL
26P/N 211455F 08/03523.PLAYING SURFACE4022.4After concrete has cured, remove tape, install pole cap (40),fit pole assembly into sleeve (4). IMPORTANT!
08/03 P/N 211455F27Starting with nuts flush against bracket,secure rim and bracket to backboard. NOTE A: Do not use washers here onspring return styl
28P/N 211455F 08/0326.10 ft.(3.05 m)3818B.A.C.25.A. While holding handle, remove pin (26).B. Move elevator up or down to desired height.C. Replace pin
08/03 P/N 211455F3FAILURE TO FOLLOW THESE WARNINGS MAY RESULTIN SERIOUS INJURY AND/OR PROPERTY DAMAGE.Owner must ensure that all players know and foll
4P/N 211455F 08/032213201251 2/99HEIGHT ADJUSTMENTTO ADJUST BACKBOARD:1. While holding handle, remove pin.2. Move elevator up or down todesired height
08/03 P/N 211455F5For more information on assembly, placement, properuse, and maintenance, visit The American BasketballCouncil website at http://www.
6P/N 211455F 08/03PARTS LIST - (See Hardware Identifier)See Hardware IdentifierItemQty. Part No. Description1 1 914822 Top Pole Section2 1 990062 Midd
08/03 P/N 211455F7HARDWARE IDENTIFIER (BOLTS & SCREWS)HARDWARE IDENTIFIER (NUTS & WASHERS)HARDWARE IDENTIFIER (STEEL SPACERS)HARDWARE IDENTIFI
8P/N 211455F 08/03TOOLS REQUIRED FOR THIS SECTIONHARDWARE USED IN THIS SECTION(not actual size)SECTION A: ASSEMBLE THE POLE This is what your system w
08/03 P/N 211455F91TOPMIDDLEBOTTOM231.Mark pole sections with tape (not supplied) at indicated distances from ends asshown.Tape (Not Supplied)18"
Comments to this Manuals