101/04 P/N 211475© COPYRIGHT 2000 by HUFFY SPORTSToll-Free Customer Service Number for U.S: 1-800-558-5234,For Canada: 1-800-284-8339,For Europe: 00
10P/N 211475 01/043.Align top holes of top pole to bottom holes of bottom pole. While maintainingalignment, bounce top and middle pole assembly (1 &am
01/04 P/N 21147511TOOLS REQUIRED FOR THIS SECTIONHARDWARE USED IN THIS SECTION(not actual size)SECTION B: ASSEMBLE THE BASE This is what your system
12P/N 211475 01/041.2.Insert axle (5) through wheel bracket (4). Secure wheels (6) to axle usingpushnuts (7). Carefully tap pushnuts onto axle with ha
01/04 P/N 211475131115104.Attach pole assembly to base usingcarriage bolts (15) washers(10) and nuts(11) as shown. Two people are requiredfor this ste
14P/N 211475 01/045.Rotate non-secured ends of tank struts (16) outward to mounting holes in tank asshown.Secure ends of tank struts (16) to tank as s
01/04 P/N 21147515TOOLS REQUIRED FOR THIS SECTIONHARDWARE USED IN THIS SECTION(not actual size)SECTION C: ASSEMBLE THE ELEVATOR & BACKBOARDThis is
16P/N 211475 01/041.Install pole mount bracket (28) and reinforcement bracket (18) with carriage bolts(22) as shown. Tighten flange nuts (11) complet
01/04 P/N 211475173.28112735352619Apply logo and height indicator labels (23) toadjustment rod (51) as shown. Attach handleparts (52, 53) to adjustme
18P/N 211475 01/04Insert handle assembly through pole mount assembly asshown. Lock pole assembly in place at the 10’ (3.05 m)mark with pin (27).275.6
01/04 P/N 211475197.Attach lower elevator tubes (34) and counter balance spring (48) to backboardsupport brackets (45) using spacers (49), bolt (50),
2P/N 211475 01/04WARNING FAILURE TO FOLLOW THESE WARNINGS MAY RESULTIN SERIOUS INJURY AND/OR PROPERTY DAMAGE.Owner must ensure that all players know
20P/N 211475 01/048.Starting with nuts (11) flush against bracket (45) secure rim (40) and bracket tobackboard. IMPORTANT! For spring loaded rim assem
01/04 P/N 2114752121 21 472534132325020342010.Support pole on sawhorse. Attach backboard assembly to top pole section (1)as shown. Install pole cap
22P/N 211475 01/0412.Insert bolt (50) through left side upper elevator tube (33), then stretch spring(48) onto bolt (50). Insert bolt (50) through ri
01/04 P/N 211475231.SECTION D: SECURING THE SYSTEMRoll assembly to desired playing area. Secure assembly to ground using rope (56)and tie down stake
24P/N 211475 01/04SECTION E: INSTALL FRONT COVER1.Install front cover (38) by lining up stand-offs along the tank struts. Insert a tie strap(39) throu
01/04 P/N 211475251.Install clips.CLIP “ARM”CLIP “BODY”Insert one “arm” of clip into ram as shown. Twist “body” ofclip slightly so that second “arm” s
26P/N 211475 01/04Insert net into bottom of clip as shown.SIDE VIEWTwist net until it snaps into position.Net must be centered through clip. NETNETCLI
01/04 P/N 211475272213TO ADJUST BACKBOARD:1. While holding handle, remove pin.2. Move elevator up or down todesired height.3. Replace pin full length
28P/N 211475 01/04SECTION H: HEIGHT ADJUSTMENT 1.A. While holding handle, remove pin (27).B. Move elevator up or down to desired height.C. Replace pin
01/04 P/N 2114753IMPORTANT!Remove all contents from boxes.Be sure to check inside pole sections;hardware and additional parts are packed inside.NOTICE
4P/N 211475 01/04Get to know the basic parts of your basketball system...FRONTTOP POLEBACKMIDDLE POLEFRONTCOVERRIMBOTTOMPOLESTRUTSELEVATORASSEMBLYBA
01/04 P/N 2114755Item Qty Part No. Description1 1 908026 Top Pole Section2 1 908107 Middle Pole Section (with Label)3 1 908015 Bottom Pole Section4 1
6P/N 211475 01/04HARDWARE IDENTIFIER (BOLTS & SCREWS)Item #14 (2)Item #31 (4)Item #55 (1)Item #44 (4)Item #11 (15)Item #9 (6)Item #50 (6)Item #19
01/04 P/N 2114757Item #20 (8)Item #42 (1)2213TO ADJUST BACKBOARD:1. While holding handle, remove pin.2. Move elevator up or down todesired height.3. R
8P/N 211475 01/04BEFORE YOU START!To ensure optimal playability of backboard system, a close tolerance fit between the elevatorcomponents and hardware
01/04 P/N 2114759SECTION A: ASSEMBLE THE POLES 2.WARNINGLABEL213Taped Reference MarkTaped Reference Mark1.Mark pole sections with tape (not supplied)
Comments to this Manuals