103/04 P/N 21147703© COPYRIGHT 2000 by HUFFY SPORTSToll-Free Customer Service Number for U.S: 1-800-558-5234,For Canada: 1-800-284-8339,For Europe: 0
10P/N 21147703 03/04Align dimple of middle pole with slot of bottom pole. While maintaining alignment, bouncetop and middle pole assembly (1 & 2)
03/04 P/N 2114770311TOOLS REQUIRED FOR THIS SECTIONHARDWARE USED IN THIS SECTION(not actual size)SECTION B: ASSEMBLE THE BASE This is what your syste
12P/N 21147703 03/041115102.Attach pole assembly to base using carriagebolts (15) washers(10) and nuts (11) asshown. Two people are required for this
03/04 P/N 21147703133.Rotate non-secured ends of tank struts (16) outward to mounting holes in tank asshown.Secure ends of tank struts (16) to tank as
14P/N 21147703 03/045.6.Insert axle (5) through wheel bracket (4). Secure wheels (6) to axle usingpushnuts (7). Carefully tap pushnuts onto axle with
03/04 P/N 2114770315TOOLS REQUIRED FOR THIS SECTIONHARDWARE USED IN THIS SECTION(not actual size)SECTION C: ASSEMBLE THE ELEVATOR & BACKBOARDThis
16P/N 21147703 03/041.Install pole mount bracket (28) and reinforcement bracket (18) with carriage bolts(22) as shown. Tighten flange nuts (11) compl
03/04 P/N 21147703173.28112735352619Apply logo and height indicator labels (23) toadjustment rod (51) as shown. Attach handleparts (52, 53) to adjust
18P/N 21147703 03/04Insert handle assembly through pole mount assembly asshown. Lock pole assembly in place at the 10’ (3.05 m)mark with pin (27).275
03/04 P/N 21147703197.5048494521Attach lower elevator tubes (34) and counter balance spring (48) to backboardsupport brackets (45) using spacers (46 &
2P/N 21147703 03/04WARNING FAILURE TO FOLLOW THESE WARNINGS MAY RESULTIN SERIOUS INJURY AND/OR PROPERTY DAMAGE.Owner must ensure that all players kn
20P/N 21147703 03/048.Attach upper elevator tubes (33) to backboard support brackets (45) usingspacers (46 & 49), bolt (50), and nut (21) as shown
03/04 P/N 211477032121 21 47253413232502034209.Support pole on sawhorse. Attach backboard assembly to top pole section (1)as shown. Install pole cap
22P/N 21147703 03/04334821335111.Insert bolt (50) through left side upper elevator tube (33), then stretch spring(48) onto bolt (50). Insert bolt (50
03/04 P/N 21147703231.SECTION D: SECURING THE SYSTEMRoll assembly to desired playing area. Secure assembly to ground using rope (56)and tie down stak
24P/N 21147703 03/04SECTION E: INSTALL FRONT COVER1.Install front cover (38) by lining up stand-offs along the tank struts. Insert a tie strap(39) thr
03/04 P/N 21147703251.Install clips.CLIP “ARM”CLIP “BODY”Insert one “arm” of clip into ram as shown. Twist “body” ofclip slightly so that second “arm”
26P/N 21147703 03/04Insert net into bottom of clip as shown.SIDE VIEWTwist net until it snaps into position.Net must be centered through clip. NETNETC
03/04 P/N 21147703272213TO ADJUST BACKBOARD:1. While holding handle, remove pin.2. Move elevator up or down todesired height.3. Replace pin full lengt
28P/N 21147703 03/04SECTION H: HEIGHT ADJUSTMENT 1.A.While holding handle, remove pin (27).B.Move elevator up or down to desired height.C.Replace pin
03/04 P/N 211477033IMPORTANT!Remove all contents from boxes.Be sure to check inside pole sections;hardware and additional parts are packed inside.NOTI
4P/N 21147703 03/04Get to know the basic parts of your basketball system...FRONTTOP POLEBACKMIDDLE POLEFRONTCOVERRIMBOTTOMPOLESTRUTSELEVATORASSEMBLY
03/04 P/N 211477035Item Qty Part No. Description1 1 908026 Top Pole Section2 1 908107 Middle Pole Section (with Label)3 1 908015 Bottom Pole Section4
6P/N 21147703 03/04HARDWARE IDENTIFIER (BOLTS & SCREWS)Item #14 (2)Item #31 (4)Item #55 (1)Item #44 (4)Item #11 (21)Item #9 (6)Item #50 (6)Item #1
03/04 P/N 211477037Item #20 (8)Item #42 (1)2213TO ADJUST BACKBOARD:1. While holding handle, remove pin.2. Move elevator up or down todesired height.3.
8P/N 21147703 03/04BEFORE YOU START!To ensure optimal playability of backboard system, a close tolerance fit between the elevatorcomponents and hardwa
03/04 P/N 211477039SECTION A: ASSEMBLE THE POLES WARNINGLABEL213I.D. LabelI.D. Label1.Correctly identify each pole section. 2.WOOD SCRAP(NOT SUPPLIED)
Comments to this Manuals