106/03 P/N 211543BCustomer ServiceN53 W24700 South Corporate CircleSussex, WI 53089U.S.A.A Huffy CompanyIMPORTANT! We appreciate your purchasing one
P/N 211543B 06/031019.5518.Insert handle assembly through pole mountassembly as shown. Lock pole assembly in place atthe 10’ (3.05m) mark with pin (5
1106/03 P/N 211543B2759594221.2929238829REFER TOINSTRUCTIONSINCLUDED WITH RIMHARDWARE FORRIM ASSEMBLY2322.Attach lower elevator tubes (29) to backboar
P/N 211543B 06/031227214221222223.422121272729424324.Attach backboard assembly to pole section (11).Then install pole cap (43). NOTE: Two peopleare r
1306/03 P/N 211543B4227292947595926.Insert handle assembly through pole mountassembly as shown. Lock pole assembly inplace at the 10’ (3.05m) mark wi
P/N 211543B 06/03141.Attach elevator bracket (36)and reinforcement bracket (41)to pole section (11) using bolts(16) and nuts (8) as shown.411136168232
1506/03 P/N 211543BBend top of backboard brackets (23) outward to match up with holes on backboard and secure usingnuts (8) and bolts as shown. Attac
P/N 211543B 06/03162021422156565.6.Attach upper elevator tubes (21) to backboard brackets (23) using spacers (56) bolt (20) and nut (42)as shown.Attac
1706/03 P/N 211543B56631285317.Fig. AFig. B6Insert locking pin (28) into bracket on adjustmenttube (6). Insert cross pin (5) through hole in bracketa
P/N 211543B 06/03182863153285031538.Fig. CInsert spring (53) into back of locking pin (28) as shown. Spring (53) should rest between twosmall ribs at
1906/03 P/N 211543B27595964261616161619.10.11.6463366262629Attach adjustment tube to lower elevator tubesusing bolt spacers and nut as shown.Finish ha
P/N 211543B 06/032Install display boards in the marked locations. Each mounting location consists of a mounting polestub with the following dimension
P/N 211543B 06/0320TWO PERSON MINIMUMREQUIRED FOR THISPROCEDURE. NOT FOLLOWINGRECOMMENDATION MAYRESULT IN BODILY INJURY. WARNINGAssemble 40” fan ba
2106/03 P/N 211543BItem #26 (2)ItemQty. Part No. Description1 2 900033 Back Bracket2 2 203796 T-Bolt, 3/8-16 x 53 2 200318 Bracket4 2 203472 Spring5 1
P/N 211543B 06/0322Item #27 (13)Item #18 (2)Item #20 (2)Item #33 (24)Item #35 (6)22 of 22Item #30 (8)Item #39 (4)*Item #40 (2)Item #59 (8)Item #60 (2)
306/03 P/N 211543B23487Assemble rims as shown below.13.5.4.RIM ASSEMBLY - Corner Locations 1 and 2
P/N 211543B 06/0346.WARNING: Use of this product without proper installation of netclips, or when all net clips are not present could result in bodil
506/03 P/N 211543BInsert net into bottom of clip as shown.SIDE VIEWTwist net until it snaps into position.Net must be centered through clip. NETNETCLI
P/N 211543B 06/036At corner locations 1, 2, and 3 install the display pole (11) to the mounting pole stub. If required, secure thedisplay pole (11),
706/03 P/N 211543B811491610.11.1730245251493012.4985554545744575513.4884645264725Install pole mount bracket (49) withcarriage bolts (16) as shown.Tigh
P/N 211543B 06/0383714.38382424171729293939593742Refer ToInstructionsIncluded With RimHardware For RimAssembly.8815.5927Attach backboard support brack
906/03 P/N 211543B17.16.21212759374259Attach upper elevator tubes (21) to backboard supportbrackets (37) using spacers (59), bolt (27), and nut (42)as
Comments to this Manuals